Data-Driven Structural Performance Assessment of 3D-Printed Spatial Lattice Architectures
Keywords:
3D-printed lattices; spatial lattice architectures; structural performance; data-driven surrogate modeling; uncertainty quantification; homogenizationAbstract
Three-dimensional printed spatial lattice architectures concentrate material along connected struts and nodes, producing stiffness, strength, and buckling behavior that cannot be inferred reliably from bulk material properties alone. Their performance is governed by coupled geometric, topological, and process-induced effects, including strut slenderness, nodal connectivity, manufacturing deviations, and anisotropic as-built properties. This article formulates a data-driven assessment framework for spatial lattice architectures that links design and process descriptors to homogenized and structural performance labels through physics-based simulation, surrogate modeling, and uncertainty quantification. The contribution is a coherent assessment logic rather than a single fitted model: lattice geometry is parameterized by graph-based and continuum descriptors; effective elastic properties, compliance, and buckling margins are defined through representative-volume homogenization and finite element analysis; and Gaussian-process surrogates with active learning are used to approximate performance across design space. Bayesian calibration separates process variability from model-form uncertainty, while explicit error modes address scale separation, nodal defects, print orientation, and extrapolation beyond the training domain. The framework clarifies how sparse, heterogeneous data from simulation and calibrated testing can be combined without treating surrogate predictions as validated design allowables. It also provides decision rules for when low-cost surrogate screening is defensible and when high-fidelity analysis or physical qualification remains necessary. These results are significant for the design and qualification of additively manufactured lattice components because they make performance assessment auditable, uncertainty-aware, and compatible with the geometric complexity of spatial wireframe architectures.
References
1. Gibson, L. J., & Ashby, M. F. (1997). Cellular solids: Structure and properties (2nd ed.). Cambridge University Press.
2. Deshpande, V. S., Ashby, M. F., & Fleck, N. A. (2001). Foam topology: Bending versus stretching dominated architectures. Acta Materialia, 49(6), 1035–1040.
3. Schaedler, T. A., Jacobsen, A. J., Torrents, A., Sorensen, A. E., Lian, J., Greer, J. R., Valdevit, L., & Carter, W. B. (2011). Ultralight metallic microlattices. Science, 334(6058), 962–965.
4. Meza, L. R., Das, S., & Greer, J. R. (2014). Strong, lightweight, and recoverable three-dimensional ceramic nanolattices. Science, 345(6202), 1322–1326.
5. Zheng, X., Lee, H., Weisgraber, T. H., Shusteff, M., DeOtte, J., Duoss, E. B., Kuntz, J. D., Biener, M. M., Ge, Q., Jackson, J. A., Kucheyev, S. O., Fang, N. X., & Spadaccini, C. M. (2014). Ultralight, ultrastiff mechanical metamaterials. Science, 344(6190), 1373–1377.
6. Fleck, N. A., Deshpande, V. S., & Ashby, M. F. (2010). Micro-architected materials: Past, present and future. Proceedings of the Royal Society A, 466(2121), 2495–2516.
7. Ashby, M. F. (2006). The properties of foams and lattices. Philosophical Transactions of the Royal Society A, 364(1838), 15–30.
8. Bendsøe, M. P., & Sigmund, O. (2003). Topology optimization: Theory, methods and applications. Springer.
9. Liu, J., Gaynor, A. T., Chen, S., Kang, Z., Suresh, K., Takezawa, A., Li, L., Kowsari, K., Chen, T., & To, A. C. (2018). Current and future trends in topology optimization for additive manufacturing. Structural and Multidisciplinary Optimization, 57(6), 2457–2483.
10. Zienkiewicz, O. C., Taylor, R. L., & Zhu, J. Z. (2013). The finite element method: Its basis and fundamentals (7th ed.). Butterworth-Heinemann.
11. Maconachie, T., Leary, M., Lozanovski, B., Zhang, X., Qian, M., Faruque, O., & Brandt, M. (2019). SLM lattice structures: Properties, performance, applications and challenges. Materials & Design, 183, 108137.
12. Lozanovski, B., Leary, M., Tran, P., Shidid, D., Qian, M., Choong, P., & Brandt, M. (2019). Computational modelling of strut defects in SLM manufactured lattice structures. Materials & Design, 171, 107671.
13. Murr, L. E., Gaytan, S. M., Ramirez, D. A., Martinez, E., Hernandez, J., Amato, K. N., Shindo, P. W., Medina, F. R., & Wicker, R. B. (2012). Metal fabrication by additive manufacturing using laser and electron beam melting technologies. Journal of Materials Science & Technology, 28(1), 1–14.
14. Frazier, W. E. (2014). Metal additive manufacturing: A review. Journal of Materials Engineering and Performance, 23(6), 1917–1928.
15. Calignano, F., Manfredi, D., Ambrosio, E. P., Biamino, S., Lombardi, M., Atzeni, E., Salmi, A., Minetola, P., Iuliano, L., & Fino, P. (2017). Overview on additive manufacturing technologies. Proceedings of the IEEE, 105(4), 593–612.
16. Rasmussen, C. E., & Williams, C. K. I. (2006). Gaussian processes for machine learning. MIT Press.
17. Yu, L., & Luo, D. (2018). Mesh optimisation for spatial wireframe robotic 3d printing. International Journal of Rapid Manufacturing, 7(2-3), 169-185.
18. Bessa, M. A., Bostanabad, R., Liu, Z., Hu, A., Apley, D. W., Brinson, C., Chen, W., & Liu, W. K. (2017). A framework for data-driven analysis of materials under uncertainty: Countering the curse of dimensionality. Computer Methods in Applied Mechanics and Engineering, 320, 633–667.
19. Liu, Y., Zhao, T., Ju, W., & Shi, S. (2017). Materials discovery and design using machine learning. Journal of Materiomics, 3(3), 159–177.
20. Kennedy, M. C., & O'Hagan, A. (2001). Bayesian calibration of computer models. Journal of the Royal Statistical Society: Series B (Statistical Methodology), 63(3), 425–464.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Journal of Intelligent Engineering Systems

This work is licensed under a Creative Commons Attribution 4.0 International License.