Adaptive Control of Robotic Winding Processes Under Variable Material and Environmental Conditions
Keywords:
robotic filament winding; adaptive control; tension regulation; parameter estimation; disturbance observer; composite manufacturingAbstract
Robotic winding of continuous fiber composites must maintain fiber tension, orientation, and compaction while material viscoelasticity, spool friction, mandrel geometry, and ambient conditions vary. Fixed-gain controllers tuned to nominal conditions can produce tension drift, fiber slippage, overlap, and void formation when the process departs from its calibration point. This paper develops an adaptive control framework for robotic winding that couples a reduced-order winding and tension model with online parameter estimation, disturbance compensation, and constraint-aware reference adaptation. The model represents winding angle through mandrel radius and axial velocity, tension evolution through supply-deposition velocity mismatch and span compliance, and material behavior through a rate-dependent constitutive relation with time-varying stiffness and damping. Adaptive laws update stiffness, damping, and friction parameters from measurable tension error using projection bounds. A disturbance observer estimates unmodeled spool, guide, and contact effects, while a reference governor adjusts tension and traverse speed when estimated states approach deposition-quality limits. Lyapunov analysis yields sufficient conditions for bounded tracking under bounded parameter variation, and sensitivity arguments identify when estimation excitation is insufficient. The framework makes controller design explicit about sensing, calibration, and failure modes such as tension loss, over-tension, slip, and path deviation. Practical implications include structured fusion of tension and position measurements, separation of slowly varying material properties from fast disturbances, and constraint-aware adaptation for variable material and environmental conditions.
References
1. Strong, A. B. (2008). Fundamentals of composites manufacturing: Materials, methods, and applications (2nd ed.). Society of Manufacturing Engineers.
2. Siciliano, B., Sciavicco, L., Villani, L., & Oriolo, G. (2010). Robotics: Modelling, planning and control. Springer.
3. Åström, K. J., & Wittenmark, B. (1995). Adaptive control (2nd ed.). Addison-Wesley.
4. Ioannou, P. A., & Sun, J. (1996). Robust adaptive control. Prentice Hall.
5. Krstic, M., Kanellakopoulos, I., & Kokotovic, P. (1995). Nonlinear and adaptive control design. Wiley.
6. Spong, M. W., Hutchinson, S., & Vidyasagar, M. (2006). Robot modeling and control. Wiley.
7. Chen, W.-H., Yang, J., Guo, L., & Li, S. (2016). Disturbance-observer-based control and related methods—An overview. IEEE Transactions on Industrial Electronics, 63(2), 1083–1095.
8. Bristow, D. A., Tharayil, M., & Alleyne, A. G. (2006). A survey of iterative learning control. IEEE Control Systems Magazine, 26(3), 96–114.
9. Mertiny, P., & Ellyin, F. (2002). Influence of the filament winding tension on physical and mechanical properties of reinforced composites. Composites Part A: Applied Science and Manufacturing, 33(12), 1615–1622.
10. Ou, Ya, et al. "Additive fabrication of large-scale customizable formwork using robotic fiber-reinforced polymer winding." 3D printing and additive manufacturing 9.2 (2022): 109-121.
11. Hall, D. L., & Llinas, J. (1997). An introduction to multisensor data fusion. Proceedings of the IEEE, 85(1), 6–23.
12. Ljung, L. (1999). System identification: Theory for the user (2nd ed.). Prentice Hall.
13. Khalil, H. K. (2002). Nonlinear systems (3rd ed.). Prentice Hall.
14. Qin, S. J., & Badgwell, T. A. (2003). A survey of industrial model predictive control technology. Control Engineering Practice, 11(7), 733–764.
15. Mallick, P. K. (2007). Fiber-reinforced composites: Materials, manufacturing, and design (3rd ed.). CRC Press.
16. Wisnom, M. R. (2012). The role of delamination in failure of fibre-reinforced composites. Philosophical Transactions of the Royal Society A, 370(1965), 1850–1870.
17. Hyer, M. W. (1998). Stress analysis of fiber-reinforced composite materials. McGraw-Hill.
18. Tao, F., Zhang, M., & Nee, A. Y. C. (2019). Digital twin driven smart manufacturing. Academic Press.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Journal of Intelligent Engineering Systems

This work is licensed under a Creative Commons Attribution 4.0 International License.